Slackware updating Sex trottier

6854933580_2c8b688306_z

attempting to upgrade your Slackware ARM system on the Raspberry Pi.

rpi-update is a tool created by Hexxeh for upgrading your Raspberry Pi 1/2/3 boot firmware, kernel, and kernel modules, with one simple command.

*", ATTR=="ac::a", ATTR=="0x0", ATTR=="1", KERNEL=="eth*", NAME="wlan0" #!

/bin/sh set -o nounset TOUCHPADID=$(xinput list | grep -i Synaptics) for ELEMENT in $; do if [ "$" == "id=" ]; then TOUCHPADID=$( echo $ | awk | cut -d= -f2) fi done TOUCHPADSTATE=$(xinput list $ | grep "This device is" | awk ) if [ "$" == "This device is disabled" ]; then xinput set-prop $ "Device Enabled" 1 else if [ -z "$" ]; then xinput set-prop $ "Device Enabled" 0 else echo "unknown state # lvm version # pvs -o lv_name,lv_size,lv_attr # fdisk /dev/sda && fdisk /dev/sdb Device Boot Start End Blocks Id System /dev/sda1 * 2048 104447 51200 83 Linux 50M /dev/sda2 104448 366591 131072 8e Linux 128M /dev/sda3 366592 3907029167 1953331288 8e Linux Rest - # mkfs.ext4 /dev/sda1 && mkfs.ext4 /dev/sdb1 - # pvcreate /dev/sda2 /dev/sda3 /dev/sdb2 /dev/sdb3 # vgcreate -s 32M vg00 /dev/sda3 /dev/sda2 /dev/sdb3 /dev/sdb2 - # lvcreate -L 12G -n lvol0 vg00 /dev/sda3 # lvcreate -l 59098 -n lvol1 vg00 /dev/sda3 # lvcreate -l 128 -n lvol2 vg00 /dev/sda3 - # lvconvert -m 1 --mirrorlog mirrored /dev/vg00/lvol0 /dev/sdb3 /dev/sda2 /dev/sdb2 # lvconvert -m 1 --mirrorlog mirrored /dev/vg00/lvol1 /dev/sdb3 /dev/sda2 /dev/sdb2 # lvconvert -m 1 --mirrorlog mirrored /dev/vg00/lvol2 /dev/sdb3 /dev/sda2 /dev/sdb2 # dmsetup status - # mkfs.ext4 /dev/vg00/lvol0 # mkfs.ext4 -i 65536 /dev/vg00/lvol1 # mkswap /dev/vg00/lvol2 Findings - the 96MByte partition does not fit 3x 32MByte PE. Slackware needs some manual work as there is no default initrd for the LVM scan and activation during boot. TXT from Eric Hameleers # mount -o bind /proc /mnt/proc # mount -o bind /sys /mnt/sys # mount -o bind /dev /mnt/dev # chroot /mnt # mkinitrd -c -k $(uname -r) -m ext4 -f ext4 -r /dev/vg00/lvol0 -L # mkinitrd -c -k 2.6.38 -r /dev/vg00/lvol0 -L # lspci .0 Network controller: Broadcom Corporation BCM43224 802.11a/b/g/n (rev 01) .0 0280: 14e53 (rev 01) # lshw *-network UNCLAIMED description: Network controller product: BCM43224 802.11a/b/g/n vendor: Broadcom Corporation physical id: 0 bus info: [email protected] version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:d2000000-d2003fff # modprobe -r b44 b43 b43legacy ssb the ssb module can not be removed because it is used by USB modules the Broadcom source is - as all closed source development - not up to date and needs a change in the include file src/linux/linuxver.h # PCI device 0x11ab:ox436c (sk2) SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?

Playlist Tutorials Default available Repositories: Need to run '# slpkg update' for the first time to synchronize the list of packages, also every time you add a new repository.

# xrandr --output VGA-0 --mode 1280x1024 No open source driver for the ATI X1250 yet - but as as surprise, the closed source ati driver v8.4 is working - /usr/share/ati/The swiss german keyboard needs the followed settings in Special keys...For that, users may use its little brother, compat32pkg. This is required and must refer to the directory used to store packages downloaded from multilib mirrors and from slackware-64 mirrors.By default, MULTILIBPKG_CACHE is set to /var/cache/multilibpkg.*", ATTR=="70:xx:yy:zz:bb:cc", ATTR=="0x0", ATTR=="1", KERNEL=="eth*", NAME="eth0" # PCI device 0x14e4:0x4353 (wl) SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR=="00:xx:yy:aa:bb:cc", ATTR=="0x0", ATTR=="1", KERNEL=="eth*", NAME="wlan0" # xrandr VGA-0 connected (normal left inverted right x axis y axis) 1280x1024 60.0 ...Whereas, rpi-update takes away that control and does what it's programmed to do, which is; upgrade the boot firmware, kernel, and kernel modules, after backing up any existing files.

You must have an account to comment. Please register or login here!